Crest Audio CC Series amplifiers are designed to achieve unsurpassed sonic performance and long-term reliability under extreme stress in touring or fixed installation applications. Absolute sonic accuracy is the hallmark of every Crest amplifier. Bass is solid and defined to the limits of audibility with ample current reserves. Wide-bandwidth output devices ensure detailed, transparent high frequency response. And, thanks to Crest’s exclusive IGM™ circuit, the CC Series will drive 2? loads safely without compromising performance.
The power amplifier shall consist of 2 channels. Each channel will delver a minimum of 800 watts at 8 ohms, 1.350 watts at 4 ohms, 2.000 watts at 2 ohms, 20 Hz - 20 kHz. In Bridged mono mode, it will deliver a minimum of 4.000 watts at 4 ohms, 20Hz - 20 kHz. It shall weigh 43.3 lbs. (19.64 kg). The amplifier shall incorporate protection circuitry against output short circuits, DC voltage on outputs, thermal overload and load protection due to any form of amp failure. It will include impedance sensing circuitry, a RMS clip limiter and Autoramp signal control. The amplifier shall have a sensitivity of 1.88 volts (x40) at the input, which will deliver full rated output power in any output configuration. Gain can be changed to x20. The hum and noise level shall be greater than -112 dB "A" weighted. The amplifier shall have a class H output stage with a linear power supply. The frequency response shall be greater than 10 Hz - 50 kHz, +0, -3 dB for the CC 4000 at full rated output power @ 4 ohms, .1 THD. The amplifier will operate at 230 VAC, 50 Hz (safe operating range 200-264). Front panel indicators shall include LED indicators for signal present, ACL (automatic clip limiting), Temp, and Active status. Front panel attenuators will be recessed and detented. Input connectors shall be XLR per channel. Output connectors shall be 5-way binding posts and Speakon, per channel. The packaging of the amplifier shall allow for standard rack mounting without requiring space between similar units as long as the rack is properly ventilated.
Specifications
2 Ohm Stereo - 2000 W
4 Ohm Stereo - 1350 W
8 Ohm Stereo - 800 W
4 Ohm Bridged - 4000 W
toroidal power transformer
magnetic circuit breaker on/off switch
cooled by variable speed fan with back-to-front airflow
mode selector switch for stereo, parallel and bridged-mono operation
inputs: Balanced female XLR, 1/4" TRS combi jacks
outputs: Speakon® and five-way binding posts
recessed, stepped attenuators
16-gauge steel chassis, cast aluminum front panel
Output Voltage RMS: 93 V
Frequency Response: 10 Hz - 100 kHz; +0, -2 dB at 1 watt
Power Bandwidth: 10 Hz - 35 kHz; +0, -3 dB at rated 4 ohms power
Damping factor 8 ohms at 20 Hz to 1 kHz: 500:1
Input CMRR at 1 kHz: > -65 dB
Gain: selectable between x40 (32 dB) and x20 (26 dB)
Input Sensitivity (x40) 1.88 V +/- 3% for 1 kHz, 4 ohms rated power
Input Impedance: 15 k ohms Balanced
Hum and Noise A-weighted at Rated power 8 ohms: -112 dB
Slew Rate: > 15V/us
Crosstalk 1kHz at rated power 8 ohms: -65 dB
Class: switched rail, H
Thermal Emissions 1/3 power, 4 ohms BTU/hr: 4545
Cooling: Back to front via 2 variable speed fans
Tourclass Protection Circuits: ACL™ (Active Clip Limiting), IGM (Instantaneous Gain Modulation), Autoramp™
Protection Circuits: short circuit, DC, comprehensive thermal management, current in-rush turn-on/off transient, subsonic and incorrect loads
LED indicators: Signal presence, ACL™ (Active clip limiting), Active status, Temp